VW Golf MkVII 1.4 TSI timing belt kit installation

Step-by-step fitment procedure for the 1.4 litre petrol engine used in Golfs from 2012

VW Golf MkVII 1.4 TSI timing belt kit installation

The 1.4-litre petrol engine (CHPA) used in the Golf from 2012 is a common powerplant in a popular model, so is likely to be a familiar vehicle to workshops across the country – Dayco talks us through the correct timing belt kit installation procedure.

Start by removing the plastic guard from underneath the engine and then, after taking off the front offside wheel, the lower part of the plastic cowling from inside the wheel arch.

This will reveal the auxiliary belt system and by relaxing the tension on the belt with a spanner on the tensioner, the belt can be removed.

Fig1: Before disconnecting the tensioner, lock it by inserting a pin.

Before disconnecting the tensioner, lock it by inserting a pin as shown (fig1).

Remove the cap in the engine block used to close the hole in which the crankshaft timing tool will be inserted and then disconnect the air intake to the filter box, take out the filter box and detach the pipes between the throttle and turbo, and the filter box and turbo, as well as the oil vapour recirculation pipe and the turbo air intake connector.

Now remove the water pump belt cover and the cover on the gearbox side of the intake camshaft, drain the cooling system and take off the upper cover of the water pump and the expansion tank, as the water pump and water pump belt should be changed at the same time.

Fig2: Rotate the central crankshaft pulley screw clockwise and position the intake camshaft as viewed from the gearbox side.

Detach the upper timing belt cover, which will expose the two variable valve timing units – the left the exhaust camshaft, the right the intake – and rotate the central crankshaft pulley screw clockwise and position the intake camshaft as viewed from the gearbox side as shown (figure 2).

Insert, and fully screw into place, the crankshaft timing tool (T10340) and rotate the crankshaft until the shaft rests on the tool. Then fit the camshaft tool (T10494) and after making sure it is in the correct position, lock it with a screw.

Remove the crankshaft pulley, followed by the lower timing belt cover and the two alternator retaining screws to detach it.

Fig3: Remove the plate.

Then take off the plate shown (figure 3), support the engine appropriately from above and remove the top engine mount adjacent to the timing belt and take off the central timing belt cover to access the tensioner and idler.

After removing the cover of the left (exhaust) and the central cap of the right (intake) variable valve timing units, take off the tensioner and timing belt.

Appropriately lock the valve timing units, remove the centre screws and the units themselves.

Fig4: Attach the new idler.

Attach the new idler, Dayco ATB2637 and torque to 45Nm, and tensioner, Dayco ATB2636, ensuring it is fitted as shown (figure 4), and then fit the valve timing units on the corresponding camshafts, but do not fully tighten their screws.

Fit the new timing belt, Dayco 941060 and, always rotating it (the belt) clockwise, use tool (T10499) to move the needle of the tensioner to the right about 10mm beyond the fixed reference and then back to the middle as shown (figure 5), and tighten the tensioner fixing screw to 25Nm.

Suitably lock the valve timing units and tighten their screws to 50Nm before removing the camshaft timing tools and temporarily refitting the crankshaft pully to enable the engine to be turned through a few clockwise revolutions.

Fig5: Fitting the new timing belt.

Check the belt tensioner needle remains in the right position and using the crankshaft and camshaft tools, the timing is still correct.

If so, appropriately lock the valve timing units and tighten their screws another 135 degrees.

Now remove the water pump with the belt drive and after flushing out the cooling system to remove any debris and cleaning the water pump facing, reposition the replacement pump, with the new belt, Dayco 941094 at the same time.

It is extremely important to follow the correct tightening procedure when reattaching the water pump cover, so first tighten the screws to 10Nm in the sequence shown (figure 6) and then loosen by one turn.

Fig6: Follow the correct tightening procedure.

Put a hex screw in ‘A’, torque to 30Nm and hold the torque wrench in position while retightening screws 2, 1 and 5 to 10Nm and then 3, 4, 5, 1 and 2 to 12Nm.

Refit the components in reverse order of their removal, tension the crankshaft pulley screw to 150Nm + 180 and the crankshaft timing tool cap to 30Nm.

Dayco also recommends the replacement of the auxiliary tensioner Dayco APV3270 and the auxiliary belt Dayco 6PK1000.

Finally, refill the cooling system, start the engine and carefully check for leaks and ensure the radiator fan is operating correctly.

Then, once the engine is cold, check the level of the fluid again.

To watch this installation and other Dayco technical videos, select ‘more details’ below.

Have your say!

5 8

Lost Password

Please enter your username or email address. You will receive a link to create a new password via email.