Febi is this week highlighting the active vehicle safety systems found on the BMW MINI, which was a joint development between Rover and BMW from 1995, until BMW took full control of the project in 1999.
The new MINI was first introduced in 2000 and depending on the model or options selected it was fitted with anti-lock braking (ABS), automatic stability control (ASC) or dynamic stability control (DSC), which eventually became a standard fitment in 2008.
The first generation of MINIs (R50/52/53) were equipped with a variation of the Teves Mk60 ABS unit as standard, which included electronic brake force distribution, corner brake control and engine drag torque control.
Electronic brake force distribution
Electronic brake force distribution controls the rear axle braking force and is regulated by the ABS unit which detects partial braking by the wheel speed sensor signals.
Corner brake control reduces vehicle instability that can arise when the brakes are applied while cornering at speed, by distributing brake pressure to the left and right brakes, or reducing the brake pressure to the rear axle.
Engine drag torque control prevents the driven wheels from locking up under engine braking.
Automatic stability control
Some models were also fitted with automatic stability control – variation of traction control designed to maintain directional stability under acceleration and to improve traction – and some with dynamic stability control.
In addition to ABS and ASC, dynamic stability control can also feature brake support.
Dynamic brake support automatically supplements braking output when the brakes are applied under emergency braking conditions, this is monitored by vehicle speed and brake pressure.
Maximum brake support is mainly effective when the vehicle is fully laden and the ABS control is more active on the front axle.
Then the rear axle is brought into the ABS control through increasing brake pressure.
DSC has additional sensors which include steering angle, yaw rate, transverse acceleration and hydraulic pressure to achieve the extra control.
How to identify active vehicle safety systems
You can identify the system by looking along the row of switches below the heater controls and if the vehicle is fitted with ASC or DSC it will have a switch to turn off these features from the ABS system.
Alternatively, locate the ABS unit under the bonnet, close to the bulkhead, and there will be a sticker on the motor of the ABS unit.
The braking system is an integrated part of the car’s electrical system and communicates information to other control units via the CAN bus network.
Information such as wheel speed, brake pressure, steering angle, brake lamp switch, handbrake switch, ASC or DSC switch, Yaw rate and lateral acceleration values are all used in conjunction with the engine management, supplemental restraint system (SRS), body control module and automatic gearbox ECU (if fitted), to implement the necessary braking to assist the driver.
Wheel speed sensors
Wheel speed sensors on the MINI are a magnetoresistive type and fitted into the hub assembly.
All four wheel speed sensors relay the rate of acceleration, deceleration and the direction of travel to the ABS control unit.
The speed signals are registered by the corresponding sensors 34262 (front) and 34263 (rear) and processed by the ABS control unit.
The rear left sensor is also used as the driving speed signal for the speedo, and the rear right sensor is used as an input signal for other control units, such as the automatic transmission if fitted.
The sensor is mounted in the hub at right angles to the magnetised impulse wheel that is built into the wheel bearing seal.
The active wheel speed sensor makes use of the magnetoresistive effect; a magnet in the sensor produces a magnetic field with the lines of magnetic flux running at right angles to the sensor layer.
Deflection of the lines by the impulse wheel causes changes in resistance in the thin ferromagnetic layer of the sensor element.
The sensor element converts the changes in resistance into voltages.
The square wave voltage detected by the ABS control unit is a measurement of individual wheel speed and this is used to derive the vehicle speed and is definitive for brake control.
Steering wheel angle sensor
A steering wheel angle sensor is only fitted to vehicles that are equipped with DSC.
The sensor (36081) is located at the base of the upper steering column and is designed as a potentiometer with two wipers offset by 90° (Fig 5).
The potentiometer signal is evaluated and converted into digital form to be on the CAN network.
The sensor signals provide a steering wheel angle variable, which covers the entire range of steering wheel rotation. The signal is repeated after every 360 degrees.
Voltage jumps are then evaluated thus determining the steering wheel turns.
The total angle is therefore derived from the sensor signal, the stored steering wheel angle offset, and the number of steering wheel turns.
The steering wheel angle sensor is calibrated to the individual vehicle, meaning if you replace one it must be calibrated to the ABS/DSC system using suitable diagnostic equipment.
The calibration permanently stores steering wheel position at the straight-ahead position.
DSC sensor
The DSC sensor combines the functions of the yaw rate sensor and transverse acceleration sensors and is located to the rear of the handbrake lever beneath the trim.
This sensor feeds back information to the ABS/DSC control unit on the angular rotation of the vehicle around its own vertical axis (Yaw) and lateral acceleration to determine vehicle drift.
If the control unit is replaced it will need to be calibrated using suitable diagnostic equipment.
With all its safety features built into the braking system, if the vehicle reaches its dynamic driving limits, the control unit decides whether to implement ABS control, ASC or full DSC control subject to the situation.
The Febi brand is part of the Bilstein Group, click ‘more details’ below for further information.