Everything you need to know about air suspension solenoid valve block

Specialist explains how solenoid valve blocks work, common defect symptoms and diagnosis

Everything you need to know about air suspension solenoid valve block

The valve block is a small but significant component of the air suspension system and shouldn’t be neglected when diagnosing possible system defects.

Symptoms that seem to point to a leak in an air spring, might also be a defect in the valve block.

Let’s start with explaining the general function of the part before diving deeper.

How air suspension solenoid valve blocks work

The valve block takes care of the distribution of pressurized air.

A valve block for a four-corner air suspension system with pressure reservoir contains a total of 6 air connections: one for the air compressor, four for the air springs/struts and one for the pressure reservoir.

To avoid making mistakes when installing a new valve block, all connections are color-coded.

The six solenoid valves inside the valve block are activated by the ECU (Electronic Control Unit).

It is a common misconception that the air springs are always directly fed by activation of the air compressor.

In most cases the air bellows are filled through the pressure reservoir.

The air compressor pressurizes the air in the reservoir up to 15 – 16 bar.

This pressurized air in the reservoir is used for controlled pressure build-up and as a buffer.

The general objective is to use the pressurized air as efficiently as possible, so the compressor runs as little as possible.

This prevents overheating and keeps the energy consumption low.

Defect symptoms and diagnosis

Over time the solenoid valves in the valve block can become sticky or blocked by small particles that have circulated through the system when operating.

For example, when an aging compressor breaks down, the valve block can consequentially become damaged too.

Due to overheating, small metal particles can block the solenoid valves and disturb the air distribution. Symptom: the vehicle is lower in one or more corners.

This symptom could also occur when there is a leak in the air spring.

Fortunately, the actual cause can be easily identified by swapping the concerned air line in the valve block.

If the valve block is the issue, the problem should then move to another corner.

If the problem stays on the same side, it is indeed an air leak.

The valve block is also involved in the release of excessive air pressure. If needed, the solenoid valve towards the air compressor is opened.

The pressure is then released through the pressure release valve on the compressor.

Thus, in case a vehicle stays “locked” on a certain ride height, first check the functioning of the pressure release valve on the compressor before diagnosing a faulty valve block.

If an air compressor is no longer running, the usual suspect is often the compressor itself or a faulty relay.

But it might just be the valve block.

The air suspension pressure sensor is located inside the valve block, not in the compressor.

If this sensor isn’t working correctly anymore, the signal for activating the compressor stays out and pressure is no longer built up.

If the dryer no longer has the capacity to keep moisture out of the system, the valve block can corrode internally.

Additionally, when the outside temperature drops below zero degrees Celsius, the moisture inside the valve block can freeze causing it to stop functioning.

One last thing to keep in mind is that normally the airline from the air compressor to the valve block is unpressurised if the compressor is not running. This is done to allow the compressor to start easily.

If for one of the abovementioned reasons this airline stays pressurized, much more heat is built up each time the compressor is activated.

This could lead to a burned-out compressor.

So, even though it is small, this significant component of the air suspension system deserves some attention – especially after a compressor replacement.

With more than 30 years of experience in engineering, designing and manufacturing high quality air suspension components for the aftermarket, Arnott is the technical expert when it comes to air suspension systems.

Arnott’s products are produced with high-quality, OE components offering exact form, fit and function.

Home Page Forums Everything you need to know about air suspension solenoid valve block

Viewing 1 post (of 1 total)
Viewing 1 post (of 1 total)

LEAVE A REPLY:

Reply To: Everything you need to know about air suspension solenoid valve block

Your email address will not be published. Required fields are marked *


The reCAPTCHA verification period has expired. Please reload the page.

The reCAPTCHA verification period has expired. Please reload the page.

Have your say!

2 0

Lost Password

Please enter your username or email address. You will receive a link to create a new password via email.